Stihl Serial Number Check

1. Stihl Serial Numbers And Models
2. Stihl Weedeater Serial Number
3. Stihl 011av Year Made
4. Stihl Chainsaw Serial Number Decoder

Description of the Stihl 180 ms chainsaw. Engine, purpose

The Stihl 180 ms chainsaw is a German-made chain saw. The tool runs on a two-stroke gasoline engine. The purpose of the Stihl 180 chain saw is household. The saw can be used for simple loads, for example, in the construction of structures, when cutting logs, the characteristics of the Stihl ms 180 tool allow you to work with the saw from the network, if you have a stable voltage source, the saw can be operated up to 2.5 hours without shutting down.

The basic model of 180 ms is also available in an improved version. A chain saw Stihl 180 ms c-be. A similarly marked saw has a simplified starting system. Mark MS C-be means that the saw is equipped with electronics for more efficient operation.

Not sure about the earlier models. I have 028 from early 80s. The later models, to explain your example: the 261 means they altered/fixed the design of the 260 enough that they give it a new model number. I got that tidbit from a stihl dealer and have not confirmed with an actual stihl employee. Stihl chain saws, for example, have the serial number printed on the crankcase or the motor housing. Homelite chain saws, on the other hand, have the serial number printed on the bottom side of the. Stihl chain saws, for example, have the serial number printed on the crankcase or the motor housing. Homelite chain saws, on the other hand, have the serial number printed on the bottom side of the.

Stihl 180 ms chainsaws are used for such types of work:

• Firewood sawing, construction of wooden structures;
• Preparing logs for cutting, removing bark;
• Furniture manufacture;
• Pruning of dry branches in a summer cottage, pruning of bushes and dried trees;
• Work with chipboard, OSB-plates, composite material;
• Stihl ms 180 is for wood and wood-based materials only.

Chainsaw Stihl 180 ms

Germany is a country of assembly and production of all original Stihl ms 180 chainsaws. A fake is easy to identify at a lower price. A Chinese or Polish copy of the Stihl ms 180 will cost two to three times cheaper than the original, while the build quality of such saws, of course, differs from the German one. Lighter and cheaper plastic may also be present.

The Stihl MS 180 branded saw in retail costs about 4.5-5 thousand hryvnias. The original product is always sold with a passport. The passport contains the serial number of the instrument and the engine series.

The complete set of Stihl ms 180 chainsaw includes:

• Semi-assembled chainsaw;
• Fuel tank;
• Chain, sprocket, tire;
• Chain brake;
• Lever;
• Passport;
• Instruction manual for the product.

The instructions also indicate the types of lubricant suitable for the Stihl ms 180 chainsaw. As an additional accessory, the manufacturer suggests purchasing:

• Oil filling system;
• A fueling system that makes filling gasoline safe;
• Control patterns, filing;
• A holder with which the owner can sharpen chain links with his own hands.

Technical characteristics of the Stihl 180 ms chainsaw

Characteristics of the chainsaw Stihl 180 ms:

• Power is 1500 W;
• 31.8 cc engine cm;
• Idle speed. 2800;
• Maximum speed. 9000;
• Tire 35 cm;
• Stihl Oilomatic Picco Micro 3 chain;
• Fuel tank for 250 ml of gasoline;
• Chain pitch 3/8;
• Noise level during operation 110 dB.

Stihl 180 chainsaw passport is the most important document containing all the technical characteristics of the tool. It indicates how to properly distribute gasoline for the Stihl 180 chainsaw, how to run in, how to perform maintenance.

The actual question is how many links are in the chain for the Stihl 180 chainsaw. Usually the number of links in the original Stihl branded chain is 50, but if you use chains from a different manufacturer, the number of links may be different, because the chain pitch is important, that is, the distance between the links, not their number.

User's manual

The basic rules for using the chainsaw and maintaining Stihl 180 ms in working condition:

• Assemble the saw, you need to use the tools from the kit, after assembly, run in;
• Running-in duration not less than 5 working hours;
• Troubleshoot complex problems in the service center while sawing under warranty;
• Do not disassemble the chainsaw yourself;
• It is necessary to work in protective equipment. Glasses, a mask, mittens, headphones;
• Do not use a chainsaw as an angle grinder. The tool is intended only for working with wood, they cannot cut metal!
• The maximum operating time of the chainsaw without turning off is 120 minutes;
• To refuel the chainsaw, always choose high-quality oil and gasoline;
• Disassembling the saw at home, as well as adjusting the carburetor, can not be done if you saw under warranty;
• Stihl ms 180 chainsaw oil should be selected from those recommended by the manufacturer, if the instructions do not indicate the exact brand of oil, use only original oils and greases;
• What kind of gasoline to pour into the Stihl 180 chainsaw is a question for beginners, users with experience know that the recommended type of gasoline is AI-92;
• You can only adjust the carburetor after 12 months of warranty;
• Replacement and maintenance of candles. On demand, as wear and tear, the appearance of soot;
• Filter cleaning frequency. Once a month or less, based on the frequency of operation of the chainsaw;
• Watch the chain tension; for proper tension, use the adjustment nozzle on the side panel of the chainsaw;
• Stihl 180 chainsaw chain lubrication is a regular process; follow this procedure before each operation.

Stihl Chainsaw Serial Number Check

Carb adjustment

To adjust the carburetor in the chainsaw:

• Start the saw, turn the adjusting screw for high and low revolutions to the stop. Turn it back one and a half turns.
• Warm up the saw for 5-10 minutes. Set idle screw.
• With the right settings, the circuit will not move on the bus at idle. Check saw operation for acceleration.

Chainsaw Stihl 180 ms

The sawmill is a structure in which a longitudinal cut of wood, beams, boards and other wooden objects is performed. You can create a sawmill yourself, using a chainsaw as a basis. Next, watch the about the Stihl 180 ms chainsaw:

To construct a sawmill, the owner used the following materials:

• Metal corners;
• Metal pipes;
• Metal plates;
• Steel fasteners (nuts, bolts).

In order for the sawmill to function technically correctly, lifts are needed. They are used to adjust the height of the board. Their number is at least three (for the height of the board 45 mm, 35 mm and 25 mm). It is difficult to say exactly how much material is needed to make a sawmill, this amount directly depends on the size of the structure.

Useful about a sawmill made from a chainsaw:

Sawmill is a complex structure, more designed for professionals who are developing the business of manufacturing wooden furniture, boards, blanks. Such a structure is not useful if the amount of work with the tree is small. For domestic work, you can use such an auxiliary accessory as the nozzle 'angle grinder' on a Stihl 180 chainsaw.

Faults and problem solving

What are the malfunctions in the Stihl ms 180 chainsaw and how to most effectively eliminate them?

• Chainsaw refuses to start.

Cause: The chainsaw may stall for several reasons, the first. The fuel ran out in the tank, the second. Low-quality fuel, an excessive amount of gasoline is present, and the third. The ignition system is malfunctioning.

Trouble-shooting: cleaning the filters, checking the quality of the fuel mixture, checking the lubrication level, testing the ignition and, if necessary, fixing it at a service center.

• Deteriorated cut quality.

Why is the quality of sawing reduced and what is the reason? The main one is a dumb chain. If the chain is dull, it is either sharpened or changed.

• Stihl 180 chainsaw does not start, fills the candle. In the event of such a malfunction, pay attention to the composition of the fuel mixture; a mixture that is too rich in gasoline can lead to this effect.
• The Stihl 180 chainsaw does not develop momentum. The reasons for this condition can be commonplace. Poor fuel quality, clogged fuel filter, muffler, as well as carburetor depressurization. You can adjust the carburetor of the Stihl 180 chainsaw with your own hands, but experience shows that it is better to entrust such works to the masters. Another reason why the Stihl chainsaw does not develop momentum is the nozzle blockage.
• The Stihl 180 chainsaw stalls at idle. Often there is such a malfunction, the reasons for which are the need to adjust the ignition system, defects in the parts of the piston group.

How to adjust the Stihl 180 chainsaw?

It is enough to monitor the chain tension and the constant supply of lubricant to the chain. The latest generation saws themselves can adjust the speed due to the electronics in the control system.

reviews

about disassembling and assembling a Stihl 180 chainsaw

• Metal corners;
• Metal pipes;
• Metal plates;
• Steel fasteners (nuts, bolts).

In order for the sawmill to function technically correctly, lifts are needed. They are used to adjust the height of the board. Their number is at least three (for the height of the board 45 mm, 35 mm and 25 mm). It is difficult to say exactly how much material is needed to make a sawmill, this amount directly depends on the size of the structure.

Useful about a sawmill made from a chainsaw:

Sawmill is a complex structure, more designed for professionals who are developing the business of manufacturing wooden furniture, boards, blanks. Such a structure is not useful if the amount of work with the tree is small. For domestic work, you can use such an auxiliary accessory as the nozzle 'angle grinder' on a Stihl 180 chainsaw.

Faults and problem solving

What are the malfunctions in the Stihl ms 180 chainsaw and how to most effectively eliminate them?

• Chainsaw refuses to start.

Cause: The chainsaw may stall for several reasons, the first. The fuel ran out in the tank, the second. Low-quality fuel, an excessive amount of gasoline is present, and the third. The ignition system is malfunctioning.

Trouble-shooting: cleaning the filters, checking the quality of the fuel mixture, checking the lubrication level, testing the ignition and, if necessary, fixing it at a service center.

• Deteriorated cut quality.

Why is the quality of sawing reduced and what is the reason? The main one is a dumb chain. If the chain is dull, it is either sharpened or changed.

• Stihl 180 chainsaw does not start, fills the candle. In the event of such a malfunction, pay attention to the composition of the fuel mixture; a mixture that is too rich in gasoline can lead to this effect.
• The Stihl 180 chainsaw does not develop momentum. The reasons for this condition can be commonplace. Poor fuel quality, clogged fuel filter, muffler, as well as carburetor depressurization. You can adjust the carburetor of the Stihl 180 chainsaw with your own hands, but experience shows that it is better to entrust such works to the masters. Another reason why the Stihl chainsaw does not develop momentum is the nozzle blockage.
• The Stihl 180 chainsaw stalls at idle. Often there is such a malfunction, the reasons for which are the need to adjust the ignition system, defects in the parts of the piston group.

How to adjust the Stihl 180 chainsaw?

It is enough to monitor the chain tension and the constant supply of lubricant to the chain. The latest generation saws themselves can adjust the speed due to the electronics in the control system.

reviews

about disassembling and assembling a Stihl 180 chainsaw

How to start a Stihl 180 ms chainsaw correctly:

on how to disassemble a Stihl ms 180 chainsaw for repairs:

Advanced modification ms 180. Stihl ms 180 c be chainsaw

Stihl 80 ms chainsaw reviews

Svyatoslav:

'I can say that the chainsaw is good! It was acquired in 2015. Serious failures did not happen. Due to the fact that he often used it, a candle has already been replaced several times. And I can note that this compact chainsaw is capable of performing large-scale work, despite its modest parameters and dimensions, its power corresponds to some professional saws.

Advantages: when the season of harvesting firewood is in progress, it cuts for 3-5 hours, its weight is small, its assembly is excellent and all details are very high quality. It is convenient to work with such a saw, the handles do not slip in the hands. Running a Stihl ms 180 chainsaw is as easy as double two! Followed by instructions. 5 working hours.

Disadvantages: if you need to constantly saw something, then take Stihl from the professional series, more powerful. This chainsaw even in the instructions marked as a tool for periodic use. '

Also on the pages of our blog you can read articles about:

Most serial numbers are stamped in the motor housing or crankcase to the left or right of the muffler looking down from the top on a flat surface. They will in most cases be 9 digits long and begin with the number 1, 2 or 5.

Will a 10% (E10) blend of ethanol hurt my gas-powered STIHL product?

All STIHL gasoline-powered engines can be used with up to a 10% (E10) blend of ethanol in the gasoline/engine oil mix. We also recommend that if a unit will be left unused for more than 30 days that it be stored 'dry.' This means emptying the fuel tank and then restarting and letting the unit run until all the fuel is consumed and the engine stops. For maximum performance and engine life expectancy, we also recommend using STIHL HP Ultra 2-cycle engine oil.

Stihl Serial Numbers And Models

Note: STIHL recommends use of fuel with no more than 10% ethanol content. Using fuel with greater than 10% ethanol content may cause damage to your equipment and may void your STIHL warranty. Learn More…

My chainsaw will start and idle but won't run or stalls when I go to full throttle. What's wrong?

There are several things you can check. First, make sure that you are using fresh fuel mix (never store or use fuel mix older than 60 days in can or fuel tank). Second, clean spark arrester screen in the muffler. Third, replace fuel filter in fuel tank. Fourth, clean or replace air filter. If none of these work, please take the machine to your local authorized STIHL servicing Dealer for evaluation.
Learn more about fuel concerns
Read more about storing your outdoor power equipment

Why does my chainsaw flood?

The most common reason is due to too many attempts trying to start the machine in the choke position. When starting a unit, make sure to follow the starting instructions in your instruction manual. The manual provides the proper instruction for starting procedures, but there are many conditions that may affect how the unit starts. Digital picture frame pu-10w manual. A good rule of thumb to follow is to remember that when placing the switch control to the full choke setting, more liquid fuel and less air flow into the combustion chamber in order to create a higher chance for ignition. Pulling the rope more than two to three times in this setting may flood the engine. The operator should move the Master Control Lever™ or choke lever from the full choke setting after three to four pulls even if the engine does not fire. Moving the lever to the next setting, the half choke or part throttle position will allow more air into the combustion chamber and help resolve the flooding condition.

Why does my saw leak bar oil?

The way our units lubricate a chain, most of the oil is distributed around the inside of the bar rails as it is circulated by the oil reservoirs in each drive link of the chain. The amount of oil being circulated inside the bar at any given time can be between .3 and .5 oz. As a general rule of physics, the oil will be pulled down by gravity once the chain stops turning, collecting at the bottom of the bar and seeping through the chain to puddle underneath the bar & chain assembly as well as under the drive sprocket. The fact that it appears to be continuing to seep after the unit is cut off for several days is owed to the viscosity of the oil and the anti-flinging compound (lithium) mixed with the oil at the refinery. These factors give the oil a very thick consistency, which in turn explains a slower flow rate. This condition is deemed to be normal for any chainsaw with a similar bar & chain lubricating system.
If the unit continues to seep oil after a few days, the problem may be the vacuum relief valve located in the side of the engine housing between the oil output hole and the bar stud(s). This valve has an internal spring and ball type arrangement with the ball pressed against the vent hole of the casing of the valve, when the tank develops a vacuum from the normal process of the oil being pumped out. The ball is pulled away from the hole, allowing air to enter into the tank and break the vacuum so that oil can continue to flow to the bar and chain assembly. Once the vacuum is relieved, the spring pushes the ball back against the hole of the valve casing. Sometimes debris may become trapped between the ball and the hole. This would cause the oil to keep 'weeping' because there must be some measure of vacuum in the tank to keep the oil from flowing freely once the unit is shut down. More often than not, all one needs to do is to take a small pin or needle and push it into the hole of the valve (identifiable as a small silver disk with a small hole in the center) about 6 or 7 times to loosen the debris. This should re-seal the orifice and keep the oil from seeping from the output hole when the saw is stored.

How do I adjust the bar and chain on my chainsaw?

Please refer to your instruction manual under the headings: Mounting Bar and Chain, Tensioning the Saw Chain and Checking Chain Tension.

What is kickback?

Kickback occurs when the moving saw chain near the upper quadrant of the bar nose contacts a solid object or is pinched. The reaction of the cutting force of the chain causes a rotational force on the chainsaw in the direction opposite to the chain movement. This may fling the bar up and back in an uncontrolled arc mainly in the plane of the bar. Under some cutting circumstances the bar moves towards the operator, who may suffer severe or fatal injury. Kickback may occur when the nose of the guide bar is pinched unexpectedly, unintentionally contacts solid material in the wood or is incorrectly used to begin a plunge or boring cut. It may also occur during limbing. The greater the force of the kickback reaction, the more difficult it becomes for the operator to control the saw. Many factors influence the occurrence and force of the kickback reaction. These include chain speed, the speed at which the bar and chain contact the object, the angle of contact, the condition of the chain and other factors.

What protective gear is required for chainsaw operation?

Where do I find my serial number?

Most serial numbers are stamped in the motor housing or crankcase to the left or right of the muffler looking down from the top on a flat surface. They will in most cases be 9 digits long and begin with the number 1, 2 or 5.

What do I need to know about chainsaw bar and chain lubrication?

For automatic and reliable lubrication of the saw chain and guide bar use only an environmentally compatible quality chain and bar lubricant with non-fling additive or the rapidly biodegradable STIHL BioPlus™ is recommended. The service life of the chain and guide bar depends on the quality of the lubricant. It is therefore essential to use only a specially formulated chain lubricant.
STIHL Bar and Chain Oil

Can I adjust my own carburetor?

The carburetor comes from the factory with a standard setting. This setting provides an optimum fuel-air mixture under most operating conditions. With most carburetors, it is only possible to adjust the engine idle speed within fine limits. Guitar scales. Quite often adjusting the carburetor will not solve acceleration issues. To find the correct setting for your machine, please refer to your instruction manual. If you do not have a copy of your instruction manual, please go to our product manual webpage where you can download a PDF version.

Why do the instructions tell you to wash your protective chainsaw chaps before using?

These protective garments contain pads of cut-retardant material designed to reduce the risk or severity of injury to the body parts covered by the pads in the event of contact with a rotating chain. The fibers in the pads provide extra layers of material and are designed to rip apart if they come into contact with the moving chain and to clog the sprocket and stop the chain in certain circumstances. In some contacts, the pads may stop the chain. In other contacts, the pads will resist the cutting process only for a fraction of a second. The actual degree of protection afforded will vary with the speed of the chain at the time of contact, the power and torque of the saw, the design of the chainsaw sprocket and similar factors. Follow the washing instructions. Improper care may destroy cut-retardant properties of the material. During shipping these pads may become compressed. By washing them prior to use and weekly during regular use, these pads fluff up and offer maximum protection.

My STIHL chainsaw was stolen. Do you track them?

STIHL Inc. maintains a Stolen Unit Database. If your STIHL product was stolen, please report it stolen to your local law enforcement agency. Then contact us with your name, address, model number and serial number. If the unit was registered at the time of purchase, we can have it added to the Stolen Unit Database.

Can I send my chainsaw back to STIHL for repair?

STIHL Inc. does not accept product for repair or refurbishment. Please see your local authorized full-line STIHL servicing Dealer.

What is the correct spark plug gap for my STIHL trimmer, chainsaw, or blower?

What is the minimum compression for my STIHL chainsaw?

Generally the minimum is 110 lbs. of compression. However, this will vary by model and compression readings alone are not enough to determine the condition of the engine. Compression gauges are not always accurate and different engines will provide different results.

How can I tell when my STIHL chainsaw was made?

STIHL does not incorporate production dates into our serial numbers.

Stihl Blower Serial Number Location

How often should I have my STIHL chainsaw tuned up?

Please refer to the Maintenance Schedule which can be found in the instruction manual.

Does STIHL offer an electric start chainsaw?

Stihl Weedeater Serial Number

STIHL does not offer an electric start unit. We do, however, offer our Easy2Start™ system on some models.

What is the recommended procedure for preparing my STIHL chainsaw for long term storage (over 30 days)?

Only if you plan to 'mothball' your lawn trimmer, brushcutter or chainsaw for a longer period - say during the winter months - should you pay a little more attention to the topic of 'care.' This will ensure that your equipment, when required, will be ready for action. To get the equipment ready for winter, clean it first. The air filter, the cylinder fins, the spark plug and the dismantled cutting tool should be checked and cleaned (also see Instruction Manual). Metal parts should be lightly coated with oil to protect them from rust and corrosion. The spark arresting screen in the muffler should be cleaned or replaced with a new one. The fuel tank should be emptied. Run the engine until the fuel system is dry (Warning! Do not operate the throttle. Run the equipment only at idle speed until the engine stops!) STIHL recommends the use of STIHL MotoMix^® fuel which is pre-mixed with STIHL HP Ultra synthetic oil. STIHL MotoMix^® contains no ethanol and has a storage life of up to two years. STIHL MotoMix^® can be left in the machine during seasonal storage. For winter storage, a dry and, if possible, dust-free and frost-free place would be ideal. You can save space if you hang the equipment. And remember: standard pump gasoline deteriorates. To avoid problems, only purchase enough fuel that can be used within sixty days unless it is STIHL MotoMix^®. Please refer to the Maintenance Schedule which can be found in the Instruction Manual.

Stihl 011av Year Made

My file does not appear to fit my new STIHL chain correctly. Is the chain defective?

Stihl Chainsaw Serial Number Decoder

Note that most brands of new saw chain will not exactly match the shape and fit of a round file radius and is not a defect in the chain. When STIHL saw chain is manufactured, the cutter teeth are shaped to precise angles with highly specialized machines to provide optimum performance of the new saw chain. After the manufacturing process, a simple round file of specific diameter with the appropriate file guide is recommended to help more easily maintain the cutting performance of your saw chain. While a new saw chain does not exactly match the shape and fit of a round file, a few strokes of the correct file diameter with the appropriate file guide will quickly form the shape of the cutter tooth to match the fit and radius of the file. Click here for instructions on how to sharpen STIHL Saw Chains. Additional information and instructions can also be obtained from your STIHL servicing Dealer.

What size file do I use to sharpen my saw chain?

• 3/8' PICCO chain is sharpened with a 5/32' round file
• .325' chain is sharpened with a 3/16' round file
• 3/8' chain is sharpened with a 13/64' round file